ContractorHandbook

How Many Bags of Thinset for a Shower? (12x24 Tile)

A 5 by 3 foot alcove shower tiled to 7 feet is about 92 sq ft. With 12x24 tile that takes 3 bags of 50 lb thinset and under 5 lb of grout. Here is the math.

Open the free tile calculator Free, no signup. Read on if you want the detail first.

The short answer for a standard alcove shower

Plan on 3 bags of 50 lb thinset for a 5 by 3 foot alcove shower tiled to 7 feet in 12x24 tile. That is about 92 square feet of tile, and a tile that size gets only about 40 square feet out of each bag.

The reason is the trowel. A 12x24 tile needs a deep notch and mortar on its back, so a bag goes less than half as far as it does under a 2 inch mosaic, where the calculator counts about 85 square feet per bag. The rest of this post walks through the math, so you can redo it for your own shower in the tile calculator.

Measure the shower: walls, floor and niche

Measure every surface that gets tile, in feet, and multiply width by height for each one. For a 5 by 3 foot alcove tiled to 7 feet, that gives you four numbers.

  • Back wall: 5 feet wide by 7 feet tall, 35 square feet.
  • Two side walls: 3 feet by 7 feet each, 42 square feet together.
  • Floor: 5 feet by 3 feet, 15 square feet.
  • Total: 92 square feet of tile.

A niche adds its back, top, bottom and sides. Measure them like small walls and add them in. Leave the open front of the alcove out, since it gets no tile. The square footage calculator adds up several rectangles at once if you want a check.

If you have not picked a tile yet, the tile size chart shows how many tiles of each size cover a square foot, and how much thinset each size uses.

Worked example: 92 square feet of 12x24 tile

Here is what the tile calculator returns for four common shower sizes. Every row uses 12x24 tile 3/8 inch thick, 1/8 inch grout joints, 8 tiles to a box and 10 percent waste.

A floor laid out in tiles with one tile highlighted and a waste strip alongside
The tile count is the tiled area divided by what one tile and its grout joint cover, with a 10% waste strip added and the result rounded up to whole boxes.

Thinset, tile and grout for 12x24 tile by shower size.

ShowerTile areaTilesBoxesThinset, 50 lb bagsGrout
Tub surround: 5 ft back wall and two 2.5 ft ends, 5 ft high50 sq ft28422.5 lb
Alcove walls only: 5 by 3 ft, 7 ft high77 sq ft42633.9 lb
Alcove walls and floor: 5 by 3 ft, 7 ft high92 sq ft50734.7 lb
Walk in: 5 by 4 ft, 8 ft high, walls and floor124 sq ft68946.3 lb

Tile area is before waste. The calculator adds 10 percent before it counts tiles, boxes and thinset bags. Grout and backer board are figured on the tile area itself, with no waste added.

For the 92 square foot shower, the calculator works with 101.2 square feet once waste is added. Each 12x24 tile covers 2.031 square feet with its share of the grout joint, so that is 50 tiles, 7 boxes and 3 bags of thinset. It also lists 7 sheets of 3 by 5 foot backer board, 100 spacers and 280 backer screws for the full 92 square feet. If only the walls get board, the 77 square foot walls only run gives 6 sheets.

Notice that the walls alone and the walls plus floor both land on 3 bags. Bags round up, and here the floor fits inside the third bag.

Trowel notch and bag coverage for large format tile

Thinset coverage is set by the trowel notch, not by the bag. LATICRETE's data sheet for its 4-XLT mortar lists these approximate coverages for one 50 lb bag:

  • 1/4 by 1/4 inch square notch: 80 to 95 square feet.
  • 1/4 by 3/8 inch square notch: 60 to 70 square feet.
  • 1/2 by 1/2 inch square notch: 40 to 47 square feet.

For large and heavy tile, that sheet calls for a 1/2 by 1/2 inch notch or a 3/4 inch half loop trowel. Its general wall method combs the mortar with a 1/4 by 3/8 inch notch instead. The calculator's 40 square feet per bag sits at the low end of the 1/2 inch range. That range is for the trowel alone, so it does not include mortar spread on the back of the tile. If your mortar's data sheet lets you use a smaller notch on the walls, the bags go further.

Custom Building Products says something different for its ProLite mortar. It does not recommend a 1/2 by 1/2 by 1/2 inch square notch, because the gaps between those notches make the tile harder to bed. It recommends a trowel that lets the mortar ridges collapse, such as a slanted U-notch, a V-notch or a ridged large format trowel, and says a 3/4 by 9/16 by 3/8 inch U-notch held at a 30 degree angle gives better contact between tile and substrate and the same coverage area as a 1/2 inch notched trowel. Use the trowel your own mortar's data sheet names.

Weight is not coverage, either. Custom says a 30 lb bag of ProLite covers the same area as a 50 lb bag of traditional mortar, so count bags by the coverage printed on them. The thinset and grout coverage chart lists bags and grout from 25 to 500 square feet at three tile sizes.

Back buttering and wet area coverage

A shower is a wet area, and wet areas need more mortar contact. Custom's ProLite data sheet says that, whatever trowel you use, mortar coverage between the substrate and the underside of the tile must reach 80 percent in dry areas and 95 percent in wet areas and exteriors, with every tile edge properly supported.

That is why you back butter. LATICRETE's 4-XLT sheet says to back butter tile and stone 8 by 8 inches or larger on walls, and to back butter large tiles in its large tile method. A 12x24 tile is well past that size. Custom now calls the same step flat back troweling, and it tells you to add the mortar it uses to your estimate.

Both makers tell you to check your work as you go. Pull up a tile now and then and look at the back. LATICRETE says to look for complete coverage, and to remove and replace mortar that has skinned over and is no longer sticky.

Count that mortar in your order. For the 92 square foot shower, 101.2 square feet at 40 square feet per bag is 2.53 bags of trowel coverage, so the third bag holds a little under half a bag for back buttering. Custom says to judge back troweling from the depth of the pattern on the tile's back, so check that pattern before you settle on 3 bags.

Which thinset: reading the bag label

Look for the ANSI standard numbers printed on the bag and the data sheet. LATICRETE lists 4-XLT as exceeding ANSI A118.15HT, A118.4HT and A118.11. Custom lists ProLite under ANSI A118.4TE, A118.15HET and A118.11, and says the installation must conform to ANSI A108.5. Then read the uses. 4-XLT, for example, is listed for non sag wall work and for building up to 3/4 inch under large, heavy tile.

What sits behind the tile matters too. Schluter says its KERDI shower system calls for Schluter SET, ALL-SET, FAST-SET, or an unmodified thinset meeting ANSI A118.1 for ceramic and stone tile, large format included. It says modified thinset is in general not recommended over KERDI, because it may need extended cure time before grouting.

So check the membrane before you buy the mortar. If the membrane maker names a mortar, that rule wins over any general advice, including this post. And do not count on thinset to keep water out. LATICRETE notes its mortars are not a replacement for a waterproofing membrane.

Grout for the same shower

The calculator puts the 92 square foot shower at 4.7 lb of grout with 12x24 tile and 1/8 inch joints, and grout is sold in 10 and 25 lb boxes, so one 10 lb box covers it.

A 15 square foot shower floor in 2x2 mosaic, 1/4 inch thick with 1/8 inch joints, needs 3.7 lb of grout by itself, close to the 3.9 lb that all 77 square feet of 12x24 wall tile needs, because a mosaic has far more joint per square foot. That same mosaic floor takes 1 bag of thinset on its own, at about 85 square feet per bag. For a bigger grout order, the grout for 150 sq ft preset shows the full breakdown.

Wait before you grout. LATICRETE says to grout 4-XLT after at least 24 hours of curing at 70 degrees F. Other mortars, and mortars over a membrane, follow their own data sheet.

Shopping list for a 92 square foot shower

  1. 7 boxes of 12x24 tile at 8 tiles per box, which is 50 tiles with waste.
  2. 3 bags of 50 lb thinset that your membrane maker approves.
  3. One 10 lb box of grout, for the 4.7 lb the job needs.
  4. The trowel your thinset's data sheet names for large tile.
  5. 6 sheets of 3 by 5 foot backer board for the 77 square feet of walls, if your wall system uses board.

Tiling a bathroom floor instead of a shower? Start from the 5x8 bathroom floor preset. For a bigger room, 200 square feet of 12x24 tile comes to 6 bags in the calculator, and the thinset for 200 sq ft preset shows the rest of that order.

Count the bags for your own shower

Tile calculator, Thinset and grout coverage chart, Thinset for 200 sq ft, 5x8 bathroom floor, Tile size chart. Free, no signup, nothing to install.

Questions people ask

How many square feet does a 50 lb bag of thinset cover?

It depends on the trowel. LATICRETE lists 80 to 95 square feet for 4-XLT with a 1/4 by 1/4 inch notch, 60 to 70 with a 1/4 by 3/8 inch notch, and 40 to 47 with a 1/2 by 1/2 inch notch. The tile calculator uses about 40 square feet per bag for 12x24 tile, about 60 for 12x12 and about 85 for 2x2 mosaic.

What size trowel do I need for 12x24 tile?

LATICRETE calls for a 1/2 by 1/2 inch notch or a 3/4 inch half loop trowel for large and heavy tile with 4-XLT. Custom does not recommend a 1/2 inch square notch with ProLite and points to a 3/4 by 9/16 by 3/8 inch U-notch held at a 30 degree angle. Use the trowel on your own bag's data sheet, then pull a tile to check the coverage.

Do I need to back butter 12x24 tile in a shower?

Yes. LATICRETE says to back butter tile 8 by 8 inches or larger, and Custom's data sheet says wet areas need 95 percent mortar coverage. Custom calls the step flat back troweling and says to add the mortar it uses to your estimate, because the bag coverage figures are for the trowel alone.

How much grout do I need for a shower?

With 12x24 tile and 1/8 inch joints, the calculator puts a 92 square foot alcove shower at 4.7 lb and a 124 square foot walk in shower at 6.3 lb, so one 10 lb box covers either. A 15 square foot floor of 1/4 inch thick 2x2 mosaic adds 3.7 lb on its own.

Can I use regular thinset for large format tile in a shower?

It depends on what is behind the tile. Over Schluter KERDI, Schluter calls for its own mortars or an unmodified thinset meeting ANSI A118.1, large format tile included. Over other substrates, read the bag. 4-XLT and ProLite, two mortars sold for large tile, both list ANSI A118.15. Follow the membrane maker first.

How many bags of thinset for a tub surround?

A tub surround with a 5 foot back wall and two 2.5 foot ends, tiled 5 feet high, is 50 square feet. In 12x24 tile that is 2 bags of 50 lb thinset, 4 boxes of tile and 2.5 lb of grout.

Sources